奧林巴斯HSMT-Flex掃查器 

HSMT-Flex™用于對4.5英寸管道上的圓周焊縫進行單軸編碼檢查。外型(114.3毫米)及以上。掃描儀配備了四個探針支架，但可以安裝共八個探針與可選的探針支架。安裝的探頭可以是相控陣探頭，也可以是常規UT探頭，以實現有效的檢測。

掃描儀的主要特點是其中心彎曲的能力。這使得掃描器可以安裝在更小的管道上，并將彈簧加載臂的力帶入管道的徑向，從而更好地穩定楔塊，從而獲得數據采集。出于同樣的原因，安裝在掃描儀外部的可選探頭支架也可以旋轉。

HSMT-Flex還允許它的一個側框架滑動。該特性允許將探頭安裝在掃描儀的外部。這提供了一種配置，非常適合于難以到達的地方，如管道到組件的焊接。

奧林巴斯HSMT-Flex掃查器 

標準的夾雜物

•掃描儀框架與處理，并:

?配置兩個340毫米(13.5英寸)的框架酒吧

?配置兩個500毫米(20英寸)框架桿

•與omniscan兼容的防水彈簧加載車輪編碼器與5米電纜

•90º探針托架

•4個彈簧加載臂(SLA)

•4 TOFD-P/E 31.75 mm軛架

•2pa 40mm×55mm軛架

•灌溉管和配件

注意:掃描儀不包括臍帶、探頭和楔。

選項

•臍

•遠程脈沖發生器/前置放大器

•Couplant-Feed單位

•激光引導設備

電池驅動的激光引導裝置，更容易跟蹤焊縫。

•軛

•TomoScan聚焦LT編碼器電纜適配器

•更換編碼器

•探頭夾包

組兩個彈簧臂(SLA)安裝在90º括號,允許超過四探針。

?配置大于12英寸的管道。OD。

?配置配置小于12英寸的管道。OD。

•備件包

?pv - 100應用程序

?pv - 200應用程序

The HSMT-Flex™ is intended for one axis encoded inspection of circumference welds on pipes of 4.5 in. OD (114.3 mm) and greater. The scanner comes equipped with four probe holders but can be mounted with a total of eight probes with optional probe holders. Mounted probes can be either phased array or conventional UT for most efficient inspections.

The major characteristic of the scanner is its capacity to bend in the center. This allows the scanner to fit on smaller pipes and also to bring the force of the spring-loaded arm in the radial direction of the pipes for better stability of the wedge, and therefore, optimum data acquisition. For the same reason, optional probe holders that are installed on the outside of the scanner can also pivot.

The HSMT-Flex also allows one of its side frames to slide. This feature allows having the probes mounted on the outside of the scanner. This provides a configuration that is well-suited for hard-to-reach places such as pipe-to-component welds.

Standard Inclusions

• Scanner frame with handles, and:
  • Two 340 mm (13.5 in.) frame bars
  • Two 500 mm (20 in.) frame bars
• OmniScan-compatible waterproof spring-loaded wheel encoder with 5 m cable
• Four 90º probe holder brackets
• 4 spring-loaded arms (SLA)
• 4 TOFD-P/E 31.75 mm yokes
• 2 PA 40 mm × 55 mm yokes
• Irrigation tubing and accessories

Note: Umbilical cable, probes, and wedges are not included with the scanner.

Options

• Umbilical
• Remote Pulser/Preamplifier
• Couplant-Feed Units
• Laser Guide Kit
  Battery-operated laser-guiding device for easier weld tracking.
• Yokes
• TomoScan FOCUS LT Encoder Cable Adaptor
• Replacement encoder
• Probe holder Kits
  Set of two spring-loaded arms (SLA) mounted on 90º brackets, to allow more than four probes.
  • Standard-For pipes larger than 12 in. OD.
  • Pivoting-For pipes smaller than 12 in. OD.
• Spare Parts Kits
  • For PV-100 applications
  • For PV-200 applications

Specifications