15921821180
當前位置：> 供求商機> GYcAT-SANTEST_GYcAT位移傳感器_物位傳感器
SANTEST_GYcAT位移傳感器_物位傳感器 SANTEST_GYcAT-Shanghai Hangou Mechanical And Electrical Equipment Co。，Ltd
The above mentioned accuracy applies to sensors with an effective stroke of 300mm or more. | |||||||||||||||||||||||||||||||||
Model No. |
(1):Effective Stroke
15mm-2500mm
(2):Output
A:0-10V
B:4-20mA
C:others (bipolar etc)
(3):Direction of output
(toward probe tip)
D:output data increase
R:output data decrease
(4):Thread
M:M24xP1.0 (Standard)
N:M18xP1.5
U:3/4-16UNF
(5):Sensor rod diameter
blank:Φ10 (Standard)
8:Φ8
14:Φ13.8
(6):Cable connection
CN:Connector (Standard)
G*:Pigtail type
(*:Cable length [m], Standard:1.5m)
Connector:straight type
Connector:only counter connector is supplied. In case cable needed,specify cable length.
Dimensions
Connector type (Standard) | |
| |
|
Material probe head:Al diecast, probe rod:SS304
Standard magnet:No.2P. Other magnets are available from Magnet Grouping [B].
The tip dead zone length (70mm) depends on the magnet or float type.
The length of the cable should be less than 10m in case of using the voltage output type
and 100m in case of using the current output type.
Connector:Sanwa SNW-1607-PCF (Material:zinc alloy fluoroplastic)
Applied cable diameter:Φ6.6-Φ7.5
Wire size:Less than 0.5mm2
Connection
1 DC24V
2 NC
3 0V
4 SIG COM
5 Voltage output
6 (Current output)
7 Alarm output
*Shield should be connected with 0V at user side.
SANTEST_GYcAT位移傳感器_物位傳感器 SANTEST_GYcAT-Shanghai Hangou Mechanical And Electrical Equipment Co。，Ltd
Specifications
Thanks to the Surface Mount Technology, the entire signal
processing electronics of GYcAT series is integrated into a
transducer head.
You can get a voltage or current analog signal proportional to a
magnet position only by applying a 24V dc power supply directly to
the transducer.
GYcAT series have alarm output and head is equipped with noise
cancellation functions.
Non-linearity
< ±0.05%FS TYP
Resolution
< 0.01%FS
Repeatability
< ±0.01%FS
Temp drift
40ppm FS/°C
Voltage output
0-10V or 10-0V / (output current:Max.5mA, load:Min.2kΩ)
Current output
4-20m or 20-4mA / (load:Min.500Ω)
Alarm output
Open collector 30V 0.1A
Power supply
+24 (±2) VDC (100mA)
Frequency response
Std 1kHz (depending on stroke) sampling
Admissible press.
35MPa (probe rod)
Operating Temp
-20°C-+65°C
Storage Temp
-40°C-+80°C
Vibration
6G (or 40Hz 2mmPP)
Shock
50G (2msec)
Protection
IP65
The above mentioned accuracy applies to sensors with an effective stroke of 300mm or more.
Model No.
(1):Effective Stroke
15mm-2500mm
(2):Output
A:0-10V
B:4-20mA
C:others (bipolar etc)
(3):Direction of output
(toward probe tip)
D:output data increase
R:output data decrease
(4):Thread
M:M24xP1.0 (Standard)
N:M18xP1.5
U:3/4-16UNF
(5):Sensor rod diameter
blank:Φ10 (Standard)
8:Φ8
14:Φ13.8
(6):Cable connection
CN:Connector (Standard)
G*:Pigtail type
(*:Cable length [m], Standard:1.5m)
Connector:straight type
Connector:only counter connector is supplied. In case cable needed,specify cable length.
Dimensions
Connector type (Standard)
Material probe head:Al diecast, probe rod:SS304
Standard magnet:No.2P. Other magnets are available from Magnet Grouping [B].
The tip dead zone length (70mm) depends on the magnet or float type.
The length of the cable should be less than 10m in case of using the voltage output type
and 100m in case of using the current output type.
Connector:Sanwa SNW-1607-PCF (Material:zinc alloy fluoroplastic)
Applied cable diameter:Φ6.6-Φ7.5
Wire size:Less than 0.5mm2
Connection
1 DC24V
2 NC
3 0V
4 SIG COM
5 Voltage output
6 (Current output)
7 Alarm output
*Shield should be connected with 0V at user side.
請輸入賬號
請輸入密碼
請輸驗證碼
以上信息由企業自行提供，信息內容的真實性、準確性和合法性由相關企業負責，化工儀器網對此不承擔任何保證責任。
溫馨提示：為規避購買風險，建議您在購買產品前務必確認供應商資質及產品質量。
